Welding Quality Control Analysis on Steel Structure of Pedestrian Bridge (JPO) at PMJ Land Tower Building from a Project Management Perspective
DOI:
https://doi.org/10.32832/astonjadro.v15i4.23873Keywords:
quality control, steel structure welding, AWS D1.1:2025, pedestrian bridge, project management, NDT.Abstract
Welding of steel structure components in pedestrian bridge (JPO) elements of high-rise buildings is a critical operation that determines structural integrity and user safety. Weld joint failures may reduce load-bearing capacity by 25–40%, making a comprehensive quality control system essential. Empirical studies specifically examining welding quality control for high-rise building JPO structures based on AWS D1.1:2025 and project management perspectives remain scarce in Indonesia; no published study has yet integrated technical, managerial, and human resource factors in a single quantitative model. This study aims to: (1) identify the actual implementation of welding quality control based on AWS D1.1:2025; (2) analyze factors affecting welding output quality; (3) identify dominant variables; and (4) formulate improvement recommendations. A descriptive-associative quantitative method was applied with 35 respondents — welders, Quality Control Inspectors, Welding Inspectors, Site Engineers, Field Supervisors, and Supervision Consultants — at the PMJ Land Tower Building project, East Jakarta (2024–2025). Data were collected via a 5-point Likert scale questionnaire covering 23 independent variables (X1–X23) across four dimensions: technical aspects, human resources, management & supervision, and work environment. Analysis used SPSS 26, including validity testing (Pearson, r-table = 0.334), reliability (Cronbach’s α = 0.892), normality (Kolmogorov–Smirnov), descriptive statistics, rank score analysis, and Pearson correlation. Variable mean scores ranged from 3.89 to 4.26 (Good to Very Good). The three dominant variables were Technical Training (X12, mean = 4.26), Welder Certification (X3, mean = 4.17), and WPS & PQR (X2, mean = 4.14). Work Environment (X5) and VT Effectiveness (X16) scored lowest (mean = 3.89). Correlation testing yielded r = 0.086 (p = 0.622 > 0.05), interpreted through a compliance gap — a discrepancy between positive respondent perceptions and actual field implementation. The study recommends enhancing RKS specifications, improving NDT consistency through an Inspection and Test Plan (ITP), strengthening welder qualification systems, and implementing digital documentation for improved traceability.
References
[1] American Welding Society. (2025). AWS D1.1:2025 Structural Welding Code – Steel. Miami, FL: AWS.
[2] Stenberg, T., Barsoum, Z., Åstrand, E., & Ericson Öberg, A. (2017). Quality control and assurance in fabrication of welded structures subjected to fatigue loading. Welding in the World, 61, 1003–1015. https://doi.org/10.1007/s40194-017-0490-5
[3] Project Management Institute. (2021). A Guide to the Project Management Body of Knowledge (PMBOK® Guide) (7th ed.). PMI.
[4] Kerzner, H. (2017). Project Management: A Systems Approach to Planning, Scheduling, and Controlling (12th ed.). Hoboken, NJ: John Wiley & Sons.
[5] Wardani, A., & Priyanto, A. (2024). Pengendalian mutu pada pekerjaan penggantian jembatan Progo. Jurnal Pembangunan Infrastruktur, 9(1).
[6] Hamzah, M., & Donoriyanto, D. S. (2024). Welding quality control using seven tools method at PT XYZ. The Indonesian Journal of Computer Science, 13(5). https://doi.org/10.33022/ijcs.v13i5.4412
[7] ISO. (2015). ISO 9001:2015 – Quality Management Systems. International Organization for Standardization.
[8] Juran, J. M. (2016). Juran’s Quality Handbook: The Complete Guide to Performance Excellence (7th ed.). New York: McGraw-Hill Education.
[9] ANSI. (2025). AWS D1.1:2025 Structural Welding Code – Steel: Overview of Changes. ANSI Blog.
[10] Badan Standardisasi Nasional. (2020). SNI 1729:2020 – Spesifikasi untuk Bangunan Gedung Baja Struktural (ANSI/AISC 360-16, IDT). BSN.
[11] Lu, H., Wu, Z., Zhang, Y., Wang, Y., Liu, S., Huang, H., Liu, M., & Liu, S. (2022). Towards a uniform welding quality: A novel weaving welding control algorithm based on constant heat input. Materials, 15(11), 3796. https://doi.org/10.3390/ma15113796
[12] Olugbemi, G. I. T., Isi, L. R., Ogu, E., & Owulade, O. A. (2022). Inspection-driven quality control strategies for high-tolerance fabrication and welding in industrial systems. International Journal of Multidisciplinary Research and Growth Evaluation, 3(1), 973–977.
[13] Park, H., Lee, S., & Kim, D. (2021). Qualification testing and failure analysis of SMAW welders under AWS D1.1. Materials and Design Engineering, 45(6), 109–119.
[14] Singh, P. K. (2023). Conceptualization of an intelligent decision framework for control factors and weld quality prediction. Journal of Production & Control, 11(Special Issue 06), 10–19.
[15] Hellier, C. (Ed.). (2020). Handbook of Nondestructive Evaluation (3rd ed.). New York: McGraw-Hill/AccessEngineering.
[16] American Society for Nondestructive Testing (ASNT). (n.d.). Nondestructive Testing Standards and Guidelines. ASNT.
[17] Mukherjee, S., & Gupta, P. (2023). Modern NDT applications for structural weld inspection. Engineering Structures and Materials Journal, 11(3), 201–212.
[18] Sugiyono. (2019). Metode Penelitian Kuantitatif, Kualitatif dan R&D. Bandung: Alfabeta.
[19] Mardiaman. (2021). Metodologi Penelitian Teknik Sipil. Jakarta: Universitas Tama Jagakarsa.
[20] Ramadayanti, N., & Suryadi, A. (2024). Welding quality control using the SQC method to minimise rejects at PT XYZ. International Journal of Mechanical, Industrial and Control Systems Engineering, 1(4), 43–55. https://doi.org/10.61132/ijmicse.v1i4.125
[21] Prasetyo, D., Putra, A., & Rahman, A. (2024). Implementation of AWS D1.1 for steel connections in high-rise construction. Journal of Structural Engineering Research, 18(4), 221–233.
[22] Wibowo, T., Siregar, E., & Hanung, R. (2024). Comparative study of AWS D1.1 and ASME IX for welded joints in building structures. Indonesian Journal of Civil Construction, 7(2), 66–78.
[23] Kim, J., & Cho, Y. (2023). Analysis of structural weld performance under AWS D1.1 standards. International Journal of Steel Structures, 23(1), 87–99.
[24] ISO. (2021). ISO 3834-1:2021 – Quality Requirements for Fusion Welding of Metallic Materials. Geneva: ISO.
[25] Pereira, A. B., et al. (2020). Quality assessment and process management of welded joints. Metals, 10(1), 115. https://doi.org/10.3390/met10010115
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2026 ASTONJADRO

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Paper submitted to ASTONJADRO is the sole property of the Astonjadro Journal. Unless the author withdraws the paper because he does not want to be published in this journal. The publication rights are in the journal Astonjadro.ASTONJADRO
LICENSE
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Based on a work at http://ejournal.uika-bogor.ac.id/index.php/ASTONJADRO










