PENENTUAN SETTING OPTIMAL MESIN 3D PRINTER BERBASIS FUSED DEPOSITION MODELING MENGGUNAKAN METODE TAGUCHI

Penulis

  • Anggit Prakasa Universitas Ibn Khaldun Bogor
  • Setya Permana Sutisna Universitas Ibn Khaldun Bogor
  • Anton Royanto Ahmad Universitas Ibn Khaldun Bogor

DOI:

https://doi.org/10.32832/ame.v4i2.1538

Abstrak

The 3D printers process is applied to create prototype components, but at the last 3D Printers are often applied as last products. So, high accuracy is required in this case. In this research will find the optimal
setting of the dimensional accuracy 3D printers based fused deposition modeling. The method used is
the Taguchi method, the reason for using this method its efficiency, this is because the Orthogonal
Array matrix requires less number of experiments than the classical experimental design. Analysis of
Variance is also needed in this method to see the factors that significantly influence the response
variable. The results of this study indicate that the factors that significantly influence is printspeed by
contributing 53.08%, flowrate contributes 16.4%, and temperature heater block contributes 3.85% and
optimal setting is temperature heater block 190º, print speed 60mm/s and flowrate 6.28 mm3/s. (A1,
C3 dan D2).

Referensi

L.M Galantucci ,I. Bodi, J. Kacani , F.

Lavecchia. 2015 “Analysis Of Dimensional

Performance For A 3d Open-Source

Printer Based Fused Deposition Modeling

Technique” Department of Production

and Management – Polytechnic

University of Tirana, Albania.

M.N Islam, Brian Boswell and A Pramanik

“An Investigation Of Dimensional

Accuracy Of Part Produce By Three-

Dimensional Printing”.

Stephen, B, Azimi.P., E.O. Zieneb., and

Ramos. T., 2013, “Ultrafine Particle

Emissions from Desktop 3D Printers”,

atmospheric environment volume 79(2013)

hal 334—339.

Yuan, L , 2008 , “A Preliminary Research on

Development of A Fiber-Composite, Curved

FDM system”, National University of

Singapore.

Andriani, D. Puspita.”Metode Taguchi-

Pengendalian Kualitas”. Program Studi

Teknik Industri Universitas Brawijaya.

Wahyu H Patricia, Wuryandari T, 2011.

“Optimalisasi Produk Dengan Menggunakan

Metode Perancangan Toleransi Taguchi.

Program Studi Statistika FMIPA, Universitas

Diponegoro.

Aman Muhammad. “Rekayasa Kualitas

Taguchi Dalam Perancangan Parameter

Kualitas Produk”. Program Studi Teknik

Industri, Fakultas Teknik-Universitas

Muhammadiyah Magelang.

Wahjudi D, Cahyono A. Rinaldi “Studi kasus

Optimasi Proses Sizing Benang di P.T XYZ”

Jurusan Teknik Mesin Fakultas Teknologi

Industri, Universitas Kristen Petra.

Wahjudi D, Gan Shu San, 2001. “Rekayasa

Mutu Besi Beton dengan Metode Tagucho”.

Jurusan Teknik Mesin Fakultas Teknologi

Industri, Universitas Kristen Petra.

5

Lee, Wei-chen. “Confirmation Experiment-

Chapter 6”. National Taiwan University of

Science Technology.

Diterbitkan

2018-07-01

Cara Mengutip

Prakasa, A., Sutisna, S. P., & Ahmad, A. R. (2018). PENENTUAN SETTING OPTIMAL MESIN 3D PRINTER BERBASIS FUSED DEPOSITION MODELING MENGGUNAKAN METODE TAGUCHI. AME (Aplikasi Mekanika Dan Energi): Jurnal Ilmiah Teknik Mesin, 4(2), 69–75. https://doi.org/10.32832/ame.v4i2.1538

Terbitan

Bagian

Articles